Drolet DB05130 Uživatelský manuál

45030 WOOD STOVE MANUAL STOVE BUILDER INTERNATIONAL. 1700, Léon-Harmel Québec (Qc) Canada G1N 4R9 Tel: 418-527-3060 Fax: 418-527-4311

10 Stove pipe • An adequate number of stove pipe sections. • A 90o elbow 1- Start by positioning your stove where you would like it to go,

11 5- You can now install the wall support. Simply slide the wall support up to the tee, ensuring that the adapter on the support engages wit

12 8- Finally, twist on your rain cap and you can head back inside. 9- You are now ready to connect your chimney to your stove. Simply i

13 1- Place your stove where you would like it located and use a plumb line to mark the ceiling directly above your stove flue. You will probably

14 5- Then, from beneath the support, insert the stove pipe adapter and twist-lock it into place.

15 8- Next, slide the storm collar down the chimney until it contacts the flashing. Tighten the nut and bolt and seal the collar to the chimney w

16 COUPLINGS It is very important to measure the clearance between your connectors (commonly called stove pipe) and the surrounding combustible su

17 AIR CIRCULATION SYSTEM In order to improve air circulation in the room where the wood stove is installed, certain options are available for sp

18 OPERATING YOUR DROLET WOOD STOVE FUEL Your stove was designed to burn wood only. No other type of fuel should be used. Waste and other fl

19 Smaller pieces of wood will dry faster. All logs exceeding 6" (152 mm) should be split. The wood should be stored in a place where the gr

2 TABLE OF CONTENTS INTRODUCTION...

20 HEATING Once you have obtained a good bed of embers you should reload the unit. In order to do so, open the air control completely for a few s

21 MAINTENANCE OF THE HEATING SYSTEM MAINTENANCE OF THE STOVE Our wood stoves are designed so that they will require little maintenance: - It i

22 MAINTENANCE OF THE CHIMNEY Whether you have a prefab or masonry chimney, you must conduct a visual inspection at least once a month in order to

23 FREQUENTLY ASKED QUESTIONS WHAT DO THE WORDS “DRAFT” AND “NEGATIVE PRESSURE” MEAN? The word “draft” refers to the hot air movement that ci

24 DRAWING #1 DRAWING #1 shows a stove functioning under normal and adequate conditions. Heat rises to the upper floors and the room where the st

25 DRAWING #2 DRAWING #2 shows the effect of a cold chimney. Cold air creates a reverse draft (negative pressure), which causes smoking problem

26 DRAWING #3 DRAWING #3 shows the effect of negative pressure caused by an air-moving device inside the house. In the example above, the ra

27 DRAWING #4 DRAWING #4 shows the negative pressure effect caused by wind, influenced by nearby structures such as a building.

28 DRAWING #5 DRAWING #5 shows the negative pressure effect that can be caused by wind, influenced by nearby structures such as a tree.

29 CAN I MODIFY MY STOVE TO INSTALL A GLASS DOOR? It is forbidden to modify a stove. Stoves are safety tested with a specific configuration, dra

3 INTRODUCTION THE DROLET WOOD STOVE MANUAL SBI INC., one of the most important wood stove and fireplace manufacturers in North America, congrat

30 DROLET LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. Thi

4 ASSEMBLING THE STOVE Note: This section applies to models Compak, ML, RC and Nordic only. 1- Mount the 4 legs using 2 screws per leg. 2- M

5 INSTALLING THE FIREBRICKS Note: This section applies to models Compak, ML, RC and Nordic only.

6 INSTALLATION OF YOUR DROLET WOOD STOVE POSITIONING THE STOVE It is very important to position the wood stove as close as possible to the chimne

7 CLEARANCES TO COMBUSTIBLE MATERIALS It is of utmost importance that the clearances to combustible material mentioned on your wood

8 INSTALLATION OF A HEAT RADIATION SHIELD Following the installation of a heat radiation shield, the clearances mentioned on the stove certificati

9 CHIMNEY Your wood stove may be hooked up with a prefabricated or masonry chimney. If you are using a prefab chimney, it must comply with S-629